#TECHNOSAT TS 500 UPDATE MANUALS#
#TECHNOSAT TS 500 UPDATE SERIAL NUMBER#
#TECHNOSAT TS 500 UPDATE UPDATE#
#TECHNOSAT TS 500 UPDATE SOFTWARE#

#TECHNOSAT TS 500 UPDATE UPDATE#

Latest update: TS-2000 Firmware Update Version 1.12 (July / 2015) (The latest version includes all previous updates.) If you agree with the details listed above, click the following link to download the firmware updating program. Select 'TS-2000 Update' in 'Uninstall a program' in the Control Panel and follow the instructions that appear on the display to uninstall the software. Once installation begins, follow the instructions on the screen to continue the installation.Д¬lick to read the firmware updating procedure. In the designated folder, a folder labeled 'TS2K_112' will be created.Д®xecute the Setup.exe file within the folder to begin installation. The downloaded program is only available for owners of the TS-2000/TS-2000X/TS-B2000.Д®ven if the program is downloaded, it cannot be used by owners of the Japanese models TS-2000S/SX/TS-2000V/VX.Д®xtract the downloaded file 'TS2K_112.zip' into a designated folder. When installing, running and uninstalling this program, you must have administrative privileges. We are offering the Memory Control Program MCP-2000 for this purpose. This firmware updating program cannot read and write user data (menu items, memory channels).

#TECHNOSAT TS 500 UPDATE SOFTWARE#

While the media in which the software is stored is possessed by the user, the ownership for the software itself shall be reserved for JVC KENWOOD Corporation. The user shall be allowed to use, not to resell, the software by obtaining a license from JVC KENWOOD Corporation.

#TECHNOSAT TS 500 UPDATE MANUALS#

JVC KENWOOD Corporation shall own all copyrights and other intellectual properties for the software and all manuals and documents attached to the software. The selection and introduction of the products as well as the results there from shall be upon the liability of the users. JVC KENWOOD Corporation shall not assume liability for any defects, nor warrant anything other than is expressly provided in the agreement.

The quality and performance of the software is not warranted for the applicability of any users. Users may not revise, change, translate, merge, de-compile, or reverse engineer the software. Users are required to obtain a license from JVC KENWOOD Corporation, in writing, prior to redistributing this software on a personal web page or packet radio. Larger than the recommended System Memory for each OS.ДЄ display with resolutions higher than XGA (1024 x 768).ДЄ keyboard and a mouse, or other pointing devices.ДЄn RS-232C interface.(Corresponding to COM1 to COM20).ДЄn RS-232C straight cable (D-SUB 9-pin female for the transceiver's COM port). This software is designed to run on the above operating systems.ДЄpplicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifications.ДЇaster than the recommended CPU for each OS. Windows В® 8.1 (RTM or later) (32-bit or 64-bit) Windows В® 8 (RTM or later) (32-bit or 64-bit) Windows В® 7 (Service Pack 1 or later) (32-bit or 64-bit) Windows Vista В® (Service Pack 2 or later)(32-bit or 64-bit) You can check the firmware version of your TS-2000(X)/B2000 by following procedure.

#TECHNOSAT TS 500 UPDATE SERIAL NUMBER#

You can find the serial number imprinted on the rear panel, just below the ANT1 or ANT2 connector it consists of an 8-digit number beginning with 'S/NO.'

Serial numbers: From S/NO.208xxxxx through S/NO.B58xxxxx approx. The firmware updating program is applicable for following models/units. When using a single lever paddle, the internal electronic keyer occasionally generates extra dots or dashes. We are offering the firmware updating program to the TS-2000 series owners. The All-mode Multi-bander TS-2000 series firmware has been updated as follows.

Technosat Ts 500 Update